C86300 Manganese Bronze Solid Bar Product Information Page
Atlas Bronze offers C86300 Solid Bar Manganese Bronze. C86300 Solid Bar is available as Continuous Cast Bar Stock per ASTM B505 in Standard Sizes (see below) or special mill runs depending on the total quantity that your project requires.
Manganese bronze is not used in the commercial or consumer market; it is found almost exclusively in the industrial sector. This is because of the durability and toughness of manganese bronze. It is used to make bushings, valve stems, hydraulic cylinder components and propellers. Its primary use in industry means this bronze is typically sold in large amounts, with a standard bar length of 144 inches or 12 feet.
|
Diameter (inches)
|
Part Number
|
|
0.750"
|
8630S-6
|
|
1.000"
|
8630S-8
|
|
1.250"
|
8630S-10
|
|
1.500"
|
8630S-12
|
|
1.750"
|
8630S-14
|
|
2.000"
|
8630S-16
|
|
2.500"
|
8630S-20
|
|
2.750"
|
8630S-22
|
|
3.000"
|
8630S-24
|
|
3.500"
|
8630S-28
|
|
4.000"
|
8630S-32
|
|
4.500"
|
8630S-36
|
|
4.750"
|
8630S-38
|
|
5.000"
|
8630S-40
|
|
5.500"
|
8630S-44
|
|
6.000"
|
8630S-48
|
|
6.500"
|
8630S-52
|
|
7.000"
|
8630S-56
|
|
7.125"
|
8630S-57
|
|
7.500"
|
8630S-60
|
|
8.000"
|
8630S-64
|
|
9.000"
|
8630S-72
|
|
10.00"
|
8630S-80
|
|
11.00"
|
8630S-88
|
|
12.00"
|
8630S-96
|
|
13.00"
|
8630S-104
|
C86300 SOLID BAR IS TYPICALLY USED FOR:
This material is used in a variety of applications. Typical uses for this alloy are Extra heavy duty and high strength applications.
- Large valve stems,
- gears,
- cams,
- slow-speed heavy-load bearings,
- screwdown nuts
- hydraulic cylinder parts.
C86300 SOLID BAR CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
|
Cu(1)
|
Al
|
Fe
|
Pb
|
Mn
|
Ni(2)
|
Sn
|
Zn
|
|
Min./Max.
|
60.0-66.0
|
5.0-7.5
|
2.0-4.0
|
.20
|
2.5-5.0
|
1.0
|
.20
|
22.0-28.0
|
|
Nominal
|
63.0
|
6.2
|
3.0
|
-
|
3.7
|
-
|
-
|
25.0
|
(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
Note: Cu + Sum of Named Elements, 99.0% min.
C86300 SOLID BAR MECHANICAL PROPERTIES:
NOTE: Information courtesy of Copper.org
|
Temper
|
Section
Size
|
Cold
Work
|
Typ/
Min
|
Temp
|
Tensile
Strength
|
Yield
Strength
(0.5% ext.
under load)
|
Yield
Strength
(0.2%
offset)
|
Yield
Strength
(0.05%
offset)
|
El
|
Rockwell
Hardness
|
Vickens
Hard.
|
Brinell
Hard.
|
Shear
Strength
|
Fatigue
Strength*
|
Izod
Impact
Strength
|
|
in.
|
%
|
|
F
|
ksi
|
ksi
|
ksi
|
ksi
|
%
|
B
|
C
|
F
|
30T
|
500
|
500
|
3000
|
ksi
|
ksi
|
ft-lb
|
|
mm.
|
|
|
C
|
MPa
|
MPa
|
MPa
|
MPa
|
|
|
|
|
|
|
|
|
MPa
|
MPa
|
J
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
TYP
|
68
|
119
|
62
|
-
|
-
|
18
|
-
|
-
|
-
|
-
|
-
|
-
|
225
|
-
|
25
|
15.0
|
|
0.0
|
|
|
20
|
821
|
427
|
-
|
-
|
18
|
-
|
-
|
-
|
-
|
-
|
-
|
225
|
-
|
172
|
20.0
|
|
As Centrifugal Cast
|
|
M02
|
0.0
|
0
|
SMIN
|
68
|
110
|
60
|
-
|
-
|
12
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
758
|
414
|
-
|
-
|
12
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Continuous Cast
|
|
M07
|
0.0
|
0
|
SMIN
|
68
|
110
|
62
|
-
|
-
|
14
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
758
|
427
|
-
|
-
|
14
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
SMIN
|
68
|
110
|
60
|
-
|
-
|
12
|
-
|
-
|
-
|
-
|
-
|
-
|
223
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
760
|
415
|
-
|
-
|
12
|
-
|
-
|
-
|
-
|
-
|
-
|
223
|
-
|
-
|
0.0
|
*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.
|
