C91100 Tin Bronze Plate / Rectangle
Atlas Bronze offers C91100 Tin Bronze Plate / Bridge Plate. Atlas stocks CDA 911 in Big Blocks and will cut to your custom dimensions. Our Plate dual certified to ASTM B505 and ASTM B22. This alloy is typically cast on a Made to Order basis. Please note that the method in which the material is
cast will depend on your
size, specification and desired quantity.
This
material is used in a variety of applications. Typical uses for this
alloy are: Piston rings, bearings, bushings, bridge plates.
- 4" thick x 15" wide
- 5" thick x 15" wide
- 8" thick x 18" wide
- 10" thick x 12" wide
__________________________________________________________________________________________
This material is available on a MADE TO ORDER basis. Click for a quote and be sure to enter all the specifics that you need.
 
__________________________________________________________________________________________
TYPICALLY USED FOR:
This
material is used in a variety of applications. Typical uses for this
alloy are: Piston rings, bearings, bushings, bridge plates.
CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
|
|
Cu(1)
|
Al
|
Sb
|
Fe
|
Pb
|
Ni(2)
|
P(3)
|
Si
|
S
|
Sn
|
Zn
|
|
Min./Max.
|
82.0-85.0
|
.005
|
.20
|
.25
|
.25
|
.50
|
1.0
|
.005
|
.05
|
15.0-17.0
|
.25
|
|
Nominal
|
83.5
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
16.0
|
-
|
(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
(3) For continuous castings, P shall be 1.5%, max.
Note: Cu + Sum of Named Elements, 99.4% min.
MECHANICAL PROPERTIES:
(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
|
Temper
|
Section
Size
|
Cold
Work
|
Typ/
Min
|
Temp
|
Tensile
Strength
|
Yield
Strength
(0.5% ext.
under load)
|
Yield
Strength
(0.2%
offset)
|
Yield
Strength
(0.05%
offset)
|
El
|
Rockwell
Hardness
|
Vickens
Hard.
|
Brinell
Hard.
|
Shear
Strength
|
Fatigue
Strength*
|
Izod
Impact
Strength
|
|
in.
|
%
|
|
F
|
ksi
|
ksi
|
ksi
|
ksi
|
%
|
B
|
C
|
F
|
30T
|
500
|
500
|
3000
|
ksi
|
ksi
|
ft-lb
|
|
mm.
|
|
|
C
|
MPa
|
MPa
|
MPa
|
MPa
|
|
|
|
|
|
|
|
|
MPa
|
MPa
|
J
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
TYP
|
68
|
35
|
25
|
-
|
-
|
2
|
-
|
-
|
-
|
-
|
-
|
-
|
135
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
241
|
172
|
-
|
-
|
2
|
-
|
-
|
-
|
-
|
-
|
-
|
135
|
-
|
-
|
0.0
|
|
M01
|
0.0
|
0
|
SMIN
|
68
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.
APPLICABLE SPECIFICATIONS:
NOTE: Information courtesy of Copper.org
|
Product
|
Specification
|
|
Sand
|
ASTM B22
|
|
|
|
