Oil & Grease Groove Bronze Bushings
Our Oil and Grease Groove Cast Bronze Bushings are machined from continuous cast C93200 (SAE 660) bronze for superior quality and performance. The continuous casting process assures a uniform bronze structure throughout the bearing, free from porosity and hard particle inclusions commonly found in other cast processes.
Our standard bronze bushing with oil and grease groove line features over 1,000 sizes that are carried in stock. Any of our standard stock sizes of Sleeve Bushings are adaptable to grooving and graphite plugging. You select your desired size and we add the lubricant of your choice. Unless otherwise specified, the width and depth of the oil grooves will be proportional to the wall thickness and size of the bearing, contained within the bearing.
Note: In order to form a more perfect oil film between the bearing & shaft, we recommend a V-shaped grease groove in bushings whenever the design permits, as it allows a full flow of the lubricant across the bearing surface.
1.) Choose Your Oil & Grease Groove Bronze Bushing Design:
2.) Choose Your Oil & Grease Groove Bronze Bushing Dimensions: 
C93200 CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
|
Cu(1)
|
Al
|
Sb
|
Fe
|
Pb
|
Ni(2)
|
P(3)
|
Si
|
S
|
Sn
|
Zn
|
|
Min./Max.
|
81.0-85.0
|
.005
|
.35
|
.20
|
6.0-8.0
|
1.0
|
.15
|
.005
|
.08
|
6.3-7.5
|
1.0-4.0
|
|
Nominal
|
83.0
|
-
|
-
|
-
|
7.0
|
-
|
-
|
-
|
-
|
6.9
|
2.5
|
(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
(3) For continuous castings, P shall be 1.5%, max.
Note: Cu + Sum of Named Elements, 99.0% min.
C93200 MECHANICAL PROPERTIES:
(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
|
Temper
|
Section
Size
|
Cold
Work
|
Typ/
Min
|
Temp
|
Tensile
Strength
|
Yield
Strength
(0.5% ext.
under load)
|
Yield
Strength
(0.2%
offset)
|
Yield
Strength
(0.05%
offset)
|
El
|
Rockwell
Hardness
|
Vickens
Hard.
|
Brinell
Hard.
|
Shear
Strength
|
Fatigue
Strength*
|
Izod
Impact
Strength
|
|
in.
|
%
|
|
F
|
ksi
|
ksi
|
ksi
|
ksi
|
%
|
B
|
C
|
F
|
30T
|
500
|
500
|
3000
|
ksi
|
ksi
|
ft-lb
|
|
mm.
|
|
|
C
|
MPa
|
MPa
|
MPa
|
MPa
|
|
|
|
|
|
|
|
|
MPa
|
MPa
|
J
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
TYP
|
68
|
35
|
18
|
-
|
-
|
20
|
-
|
-
|
-
|
-
|
-
|
65
|
-
|
-
|
16
|
6.0
|
|
0.0
|
|
|
20
|
241
|
124
|
-
|
-
|
20
|
-
|
-
|
-
|
-
|
-
|
65
|
-
|
-
|
110
|
8.0
|
|
As Centrifugal Cast
|
|
M02
|
0.0
|
0
|
SMIN
|
68
|
30
|
14
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
207
|
97
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Continuous Cast
|
|
M07
|
0.0
|
0
|
SMIN
|
68
|
35
|
20
|
-
|
-
|
10
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
241
|
138
|
-
|
-
|
10
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
SMIN
|
68
|
30
|
14
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
207
|
97
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.
C93200 APPLICABLE SPECIFICATIONS:
NOTE: Information courtesy of Copper.org
|
Product
|
Specification
|
|
Centrifugal
|
ASTM B271
SAE J462, J461
|
|
Continuous
|
ASTM B505
SAE J461, J462
|
|
Ingot
|
ASTM B30
|
|
Permanent Mold
|
SAE J461, J462
|
|
Sand
|
ASTM B584, B763, B66
SAE J462, J461
|
|
