C93200 Rectangle / Plate
Atlas Bronze offers C93200 Bearing Bronze, SAE 660 Rectangle / Plate stock. CDA 932 Bearing Bronze Rectangle / Plate Bar is stocked in both full bar length of 105" long or can be cut to exact desired width and length.
This material is used in a variety of Bearing / Bushing applications. Typical uses for this alloy are:
- Fuel Pump Bushings
- Water Pump Bushings
- Diesel Engine Wrist Pin Bushings
- Hydraulic Press
- Stuffing Box
- Insert Bearings
- Bearings
- Thrust Washers
|
- Pumps
- Bushings
- Machine Parts
- Pump Impellers
- General Purpose Bushings
- Fittings
- Pump Fixtures
- Machine Tool Bearings
|
TYPICALLY USED FOR:
This
material is used in a variety of applications. Typical uses for this
alloy are:
Fuel
Pump Bushings, Water Pump Bushings, Diesel Engine Wrist Pin Bushings,
Hydraulic Press Stuffing Box, Insert Bearings, Bearings, Thrust Washers,
Pumps, Bushings, Machine Parts, Pump Impellers, General Purpose
Bushings, Fittings, Pump Fixtures, Machine Tool Bearings.
CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
|
|
Cu(1)
|
Al
|
Sb
|
Fe
|
Pb
|
Ni(2)
|
P(3)
|
Si
|
S
|
Sn
|
Zn
|
|
Min./Max.
|
81.0-85.0
|
.005
|
.35
|
.20
|
6.0-8.0
|
1.0
|
.15
|
.005
|
.08
|
6.3-7.5
|
1.0-4.0
|
|
Nominal
|
83.0
|
-
|
-
|
-
|
7.0
|
-
|
-
|
-
|
-
|
6.9
|
2.5
|
(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
(3) For continuous castings, P shall be 1.5%, max.
Note: Cu + Sum of Named Elements, 99.0% min.
MECHANICAL PROPERTIES:
(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
|
Temper
|
Section
Size
|
Cold
Work
|
Typ/
Min
|
Temp
|
Tensile
Strength
|
Yield
Strength
(0.5% ext.
under load)
|
Yield
Strength
(0.2%
offset)
|
Yield
Strength
(0.05%
offset)
|
El
|
Rockwell
Hardness
|
Vickens
Hard.
|
Brinell
Hard.
|
Shear
Strength
|
Fatigue
Strength*
|
Izod
Impact
Strength
|
|
in.
|
%
|
|
F
|
ksi
|
ksi
|
ksi
|
ksi
|
%
|
B
|
C
|
F
|
30T
|
500
|
500
|
3000
|
ksi
|
ksi
|
ft-lb
|
|
mm.
|
|
|
C
|
MPa
|
MPa
|
MPa
|
MPa
|
|
|
|
|
|
|
|
|
MPa
|
MPa
|
J
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
TYP
|
68
|
35
|
18
|
-
|
-
|
20
|
-
|
-
|
-
|
-
|
-
|
65
|
-
|
-
|
16
|
6.0
|
|
0.0
|
|
|
20
|
241
|
124
|
-
|
-
|
20
|
-
|
-
|
-
|
-
|
-
|
65
|
-
|
-
|
110
|
8.0
|
|
As Centrifugal Cast
|
|
M02
|
0.0
|
0
|
SMIN
|
68
|
30
|
14
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
207
|
97
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Continuous Cast
|
|
M07
|
0.0
|
0
|
SMIN
|
68
|
35
|
20
|
-
|
-
|
10
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
241
|
138
|
-
|
-
|
10
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
SMIN
|
68
|
30
|
14
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
207
|
97
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.
APPLICABLE SPECIFICATIONS:
NOTE: Information courtesy of Copper.org
|
Product
|
Specification
|
|
Centrifugal
|
ASTM B271
SAE J462, J461
|
|
Continuous
|
ASTM B505
SAE J461, J462
|
|
Ingot
|
ASTM B30
|
|
Permanent Mold
|
SAE J461, J462
|
|
Sand
|
ASTM B584, B763, B66
SAE J462, J461
|
|
