C93700 High Leaded Tin Bronze Rectangle / Plate
Atlas Bronze offers C93700 Tin Bronze Plate, Rectangles and Castings. Atlas stocks a select variety
of sizes in
Bridge Plate, per ASTM B22. Select shapes & sizes are available Off-the-Shelf, however other sizes are typically cast on a
Made to Order basis. Please note that the method in which the material
is
cast will depend on your
size, specification and desired quantity.
__________________________________________________________________________________________
 
__________________________________________________________________________________________
TYPICALLY USED FOR:
This
material is used in a variety of applications. Typical uses for this
alloy are:
Fasteners: Washers for Engines, Industrial:
Crank Shafts, Bushings, Machine Parts, High Speed, Heavy Load Bearings,
Pumps, Pressure Tight Castings, Impellers, Bushings for high speed and
heavy pressure., Bearings, Bearing Plates, Parts for Steel Mill
Maintenance,
Marine: Large Bearings for Ships
CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
|
|
Cu
|
Al
|
Sb
|
Fe(1)
|
Pb
|
Ni(2)
|
P(3)
|
Si
|
S
|
Sn
|
Zn
|
|
Min./Max.
|
78.0-82.0
|
.005
|
.50
|
.7
|
8.0-11.0
|
.50
|
.10
|
.005
|
.08
|
9.0-11.0
|
.8
|
|
Nominal
|
80.0
|
-
|
-
|
-
|
9.5
|
-
|
-
|
-
|
-
|
10.0
|
-
|
(1) Fe shall be .35% max., when used for steel-backed
(2) Ni value includes Co.
(3) For continuous castings, P shall be 1.5%, max.
Note: Cu + Sum of Named Elements, 99.0% min.
MECHANICAL PROPERTIES:
(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
|
Temper
|
Section
Size
|
Cold
Work
|
Typ/
Min
|
Temp
|
Tensile
Strength
|
Yield
Strength
(0.5% ext.
under load)
|
Yield
Strength
(0.2%
offset)
|
Yield
Strength
(0.05%
offset)
|
El
|
Rockwell
Hardness
|
Vickens
Hard.
|
Brinell
Hard.
|
Shear
Strength
|
Fatigue
Strength*
|
Izod
Impact
Strength
|
|
in.
|
%
|
|
F
|
ksi
|
ksi
|
ksi
|
ksi
|
%
|
B
|
C
|
F
|
30T
|
500
|
500
|
3000
|
ksi
|
ksi
|
ft-lb
|
|
mm.
|
|
|
C
|
MPa
|
MPa
|
MPa
|
MPa
|
|
|
|
|
|
|
|
|
MPa
|
MPa
|
J
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
TYP
|
68
|
35
|
18
|
16
|
-
|
20
|
-
|
-
|
-
|
-
|
-
|
60
|
-
|
18
|
13
|
5.0
|
|
0.0
|
|
|
20
|
241
|
124
|
110
|
-
|
20
|
-
|
-
|
-
|
-
|
-
|
60
|
-
|
124
|
90
|
7.0
|
|
As Centrifugal Cast
|
|
M02
|
0.0
|
0
|
SMIN
|
68
|
30
|
12
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
207
|
83
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Continuous Cast
|
|
M07
|
0.0
|
0
|
SMIN
|
68
|
35
|
20
|
-
|
-
|
6
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
241
|
138
|
-
|
-
|
6
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
SMIN
|
68
|
30
|
12
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
207
|
83
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.
APPLICABLE SPECIFICATIONS:
NOTE: Information courtesy of Copper.org
|
Product
|
Specification
|
|
Bearings
|
AMS 4827
|
|
Centrifugal
|
AMS 4842
ASTM B271
SAE J462, J461
|
|
Continuous
|
ASTM B505
SAE J461, J462
|
|
Ingot
|
ASTM B30
|
|
Sand
|
AMS 4842
ASME SB584
ASTM B763, B66, B584, B22
SAE J461, J462
|
|
