C95400 | CDA954 Aluminum Bronze
Atlas Bronze offers
C95400 Aluminum Bronze, 9C in Solids, Tubes, Cored Bar, Plate, Rectangles and Castings.
This alloy is available as both a standard Off-the-Shelf product and as special castings.
We have a unique offering, by offered LARGE BLOCK PLATE, sizes up to 10" thick x 18" wide.
The method in which the material is cast will depend on your size, specification and desired quantity.
C95400 TYPICAL USES:
This material is used in a variety of applications. Typical uses for this alloy are:
- FuelPump Bushings,
- Water Pump Bushings,
- Diesel Engine Wrist Pin Bushings,
- Hydraulic Press Stuffing Box,
- Insert Bearings,
- Bearings
- Thrust Washers,
- Pumps,
- Bushings,
|
- Machine Parts,
- Pump Impellers,
- General Purpose
Bushings,
- Fittings,
- Pump Fixtures,
- Machine Tool Bearings
|
C95400 CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
|
Cu(1)
|
Fe
|
Ni(2)
|
Al
|
Mn
|
|
Min./Max.
|
83.0
|
3.0-5.0
|
0-1.5
|
10.0-11.5
|
0-0.50
|
(1) Cu + Sum of the Named Elements 99.5%
(2) Ni value includes Co.
|
Temper
|
Section
Size
|
Cold
Work
|
Typ/
Min
|
Temp
|
Tensile
Strength
|
Yield
Strength
(0.5% ext.
under load)
|
Yield
Strength
(0.2%
offset)
|
Yield
Strength
(0.05%
offset)
|
El
|
Rockwell
Hardness
|
Vickens
Hard.
|
Brinell
Hard.
|
Shear
Strength
|
Fatigue
Strength*
|
Izod
Impact
Strength
|
|
in.
|
%
|
|
F
|
ksi
|
ksi
|
ksi
|
ksi
|
%
|
B
|
C
|
F
|
30T
|
500
|
500
|
3000
|
ksi
|
ksi
|
ft-lb
|
|
mm.
|
|
|
C
|
MPa
|
MPa
|
MPa
|
MPa
|
|
|
|
|
|
|
|
|
MPa
|
MPa
|
J
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
TYP
|
68
|
85
|
35
|
-
|
-
|
18
|
-
|
-
|
-
|
-
|
-
|
-
|
170
|
47
|
28
|
16.0
|
|
0.0
|
|
|
20
|
586
|
241
|
-
|
-
|
18
|
-
|
-
|
-
|
-
|
-
|
-
|
170
|
324
|
193
|
22.0
|
|
As Centrifugal Cast
|
|
TQ50
|
0.0
|
0
|
SMIN
|
68
|
90
|
45
|
-
|
-
|
6
|
-
|
-
|
-
|
-
|
-
|
-
|
190
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
620
|
310
|
-
|
-
|
6
|
-
|
-
|
-
|
-
|
-
|
-
|
190
|
-
|
-
|
0.0
|
|
M02
|
0.0
|
0
|
SMIN
|
68
|
75
|
30
|
-
|
-
|
12
|
-
|
-
|
-
|
-
|
-
|
-
|
150
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
515
|
205
|
-
|
-
|
12
|
-
|
-
|
-
|
-
|
-
|
-
|
150
|
-
|
-
|
0.0
|
|
As Continuous Cast
|
|
TQ50
|
0.0
|
0
|
SMIN
|
68
|
95
|
45
|
-
|
-
|
10
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
655
|
310
|
-
|
-
|
10
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
M07
|
0.0
|
0
|
SMIN
|
68
|
85
|
32
|
-
|
-
|
12
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
586
|
221
|
-
|
-
|
12
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Permanent Mold Cast
|
|
M05
|
0.0
|
0
|
SMIN
|
68
|
100
|
40
|
-
|
-
|
10
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
690
|
275
|
-
|
-
|
10
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Sand Cast
|
|
TQ50
|
0.0
|
0
|
TYP
|
68
|
105
|
54
|
-
|
-
|
8
|
-
|
-
|
-
|
-
|
-
|
-
|
195
|
50
|
35
|
11.0
|
|
0.0
|
|
|
20
|
724
|
|
