C95400 Bearing Bronze Big Block Plate
Atlas Bronze offers C95400 Aluminum Bronze Big Block Plate per ASTM B505. CDA 954 Aluminum Bronze Plate
is available as Continuous Cast Bar Stock dual certified ASTM B505.
We also offer a select number of sizes in Sand Casting (ASTM B584) as well. *The method in which the material is
cast will depend on your
size, specification and desired quantity.*
Our C93200 Bearing Bronze per ASTM B505
is available in Standard thicknesses or we can cut your desired
thickness, width and length from one of our Big Blocks! We regularly
stock our C93200 Big Block Plates in a variety of sizes to achieve
optimal cutting capacity:
- 4" thick x 12.2" wide
- 5" thick x 15" wide
- 8" thick x 15-7/8" wide
- 10" thick x 12" wide
________________________________________________________________________________________
__________________________________________________________________________________________
TYPICALLY USED FOR:
This
material is used in a variety of applications. Typical uses for this
alloy are:
Fuel
Pump Bushings, Water Pump Bushings, Diesel Engine Wrist Pin Bushings,
Hydraulic Press Stuffing Box, Insert Bearings, Bearings, Thrust Washers,
Pumps, Bushings, Machine Parts, Pump Impellers, General Purpose
Bushings, Fittings, Pump Fixtures, Machine Tool Bearings.
CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
|
|
Cu(1)
|
Al
|
Sb
|
Fe
|
Pb
|
Ni(2)
|
P(3)
|
Si
|
S
|
Sn
|
Zn
|
|
Min./Max.
|
81.0-85.0
|
.005
|
.35
|
.20
|
6.0-8.0
|
1.0
|
.15
|
.005
|
.08
|
6.3-7.5
|
1.0-4.0
|
|
Nominal
|
83.0
|
-
|
-
|
-
|
7.0
|
-
|
-
|
-
|
-
|
6.9
|
2.5
|
(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
(3) For continuous castings, P shall be 1.5%, max.
Note: Cu + Sum of Named Elements, 99.0% min.
MECHANICAL PROPERTIES:
(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
|
Temper
|
Section
Size
|
Cold
Work
|
Typ/
Min
|
Temp
|
Tensile
Strength
|
Yield
Strength
(0.5% ext.
under load)
|
Yield
Strength
(0.2%
offset)
|
Yield
Strength
(0.05%
offset)
|
El
|
Rockwell
Hardness
|
Vickens
Hard.
|
Brinell
Hard.
|
Shear
Strength
|
Fatigue
Strength*
|
Izod
Impact
Strength
|
|
in.
|
%
|
|
F
|
ksi
|
ksi
|
ksi
|
ksi
|
%
|
B
|
C
|
F
|
30T
|
500
|
500
|
3000
|
ksi
|
ksi
|
ft-lb
|
|
mm.
|
|
|
C
|
MPa
|
MPa
|
MPa
|
MPa
|
|
|
|
|
|
|
|
|
MPa
|
MPa
|
J
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
TYP
|
68
|
35
|
18
|
-
|
-
|
20
|
-
|
-
|
-
|
-
|
-
|
65
|
-
|
-
|
16
|
6.0
|
|
0.0
|
|
|
20
|
241
|
124
|
-
|
-
|
20
|
-
|
-
|
-
|
-
|
-
|
65
|
-
|
-
|
110
|
8.0
|
|
As Centrifugal Cast
|
|
M02
|
0.0
|
0
|
SMIN
|
68
|
30
|
14
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
207
|
97
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Continuous Cast
|
|
M07
|
0.0
|
0
|
SMIN
|
68
|
35
|
20
|
-
|
-
|
10
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
241
|
138
|
-
|
-
|
10
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
SMIN
|
68
|
30
|
14
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
207
|
97
|
-
|
-
|
15
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.
APPLICABLE SPECIFICATIONS:
NOTE: Information courtesy of Copper.org
|
Product
|
Specification
|
|
Centrifugal
|
ASTM B271
SAE J462, J461
|
|
Continuous
|
ASTM B505
SAE J461, J462
|
|
Ingot
|
ASTM B30
|
|
Permanent Mold
|
SAE J461, J462
|
|
Sand
|
ASTM B584, B763, B66
SAE J462, J461
|
|
